Product ID:BLACK GLOSS ALKYD
MSDS Date:03/12/1992
FSC:8010
NIIN:00-527-2053
MSDS Number: BPTZX

PPG INDUSTRIES, INC

4325 ROSANNA DRIVE
ALLISON PARK, PA 15101
US

Emergency Phone: 304-843-1300

Info Phone: 412-492-5555/(800)245-2590/441-9695

Cage: DO894

PPG INDUSTRIES, INC.

9 ALLISON PARK, PA 15101 US

Telephone: 412-592-5555

Cage: DO894

CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

Fraction By Weight: 2-5%

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3

CALCIUM CARBONATE

CAS: 471-34-1

RTECS: FF9335000

Fraction By Weight: 20-25%

OSHA PEL 15 MG/M3

ACGIH TLV: 10 MG/M3

1000 LBS)

CAS: 1330-20-7

RTECS: ZE2100000

Fraction By Weight: 1-2%

OSHA PEL 100 PPM/150 PPM STEL

ACGIH TLV: 100 PPM/150 PPM STEL

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

MINERAL SPIRITS (SARA 313)

CAS: 64741-92-0

Fraction By Weight: 15-20%

HYDROTREATED LIGHT DISTILLATE

CAS: 64742-47-8

Fraction By Weight: 10-15%

FILM FORMERS, RESINS, AND ADDITIVES (SARA 313)

Fraction By Weight: 40-45%

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INGESTION: HARMFUL OR FATAL IF
SWALLOWED. EYE: IRRITATION. SKIN: MODERATE IRRITATION. INHALATION:
HARMFUL. IRRITATES EYES, NOSE, THROAT. IRRITATION OF RESPIRATORY
SYSTEM & PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE. INTENTIONAL
MISUSE BY DELIBERATELY CONCENTRATING AND INHALING THE CONTENTS CAN
BE HARMFUL OR FATAL.

First Aid:INGEST: DONT INDUCE VOMITING. EYE: FLUSH IMMEDIATELY W/WATER
15 MINS. SKIN: FLUSH IMMEDIATELY W/PLENTY OF WATER FOLLOWED BY
WASHING W/SOAP & WATER. INHAL: REMOVE TO FRESH AIR, APPLY ARTIF
RESPIRATION, & OTHER SUPPORTIVE MEASURES AS REQ'D. OTHER: IF
INGESTED ANY TYPE OF OVEREXPOSURE OR SYMPTOMS OCCUR/FOLLOW USE OF
PRODUCT, CONTACT POISON CONTROL CTR, EMERG ROOM OR DR IMMED. HAVE
MSDS INFO AVAILABLE

Flash Point Method:PMCC
Flash Point:107F,42C
Lower Limits:1.0
Upper Limits:U/I
Extinguishing Media:NFPA CLASS B EXTINGUISHERS(CO2, DRY CHEMICAL,
UNIVERSAL AQUEOUS FILM FORMING FOAM)FOR NFPA CLASS 2 COMBUSTIBLE
LIQ FIRES
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE, USE TO COOL
CNTNRS TO PREVENT PRESSURE BLDUP/AUTOIGNIT/EXPLOSION W/HEAT. IF
WATER IS USED FOG NOZZLES ARE PREFERRED. WEAR SCBA.
Unusual Fire/Explosion Hazard:KEEP CNTNRS CLSD. ISOLATE FROM HEAT/IGNIT
SOURCE. CLSD CNTNRS MAY EXPLODE W/HEAT. DONT APPLY TO HOT SURFACES.
TOXIC GASES MAY FORM W/FIRE/HOT SURFACE CONTACT.

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ONLY PERSONNEL
EQUIPPED WITH RESP, SKIN & EYE PROTECTION PERMITTED IN AREA. REMOVE
IGNITION SOURCES. TAKE UP SPILLED MATERIAL WITH SAWDUST,
VERMICULITE, OR OTHER ABSORBENT MATERIAL & PLACE INTO CONTAINERS
FOR DISPOSAL.

Handling and Storage Precautions:DO NOT STORE ABOVE 120 F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CASS II COMBUSTIBLE LIQUIDS.
Other Precautions:IF MAT'L PART OF MULTIPLE COMPONENT COATING SYSTEM,
READ MSDS(S) FOR OTHER COMPONENT(S) BEFORE BLENDING AS RESULTING
MIXTURE MAY HAVE HZDS OF ALL OF ITS PARTS. GROUND CONTAINERS WHEN
POURING. AVOID FR EE FALL OF LIQ IN EXCESS OF FEW INCHES.

Respiratory Protection:NIOSH/MSHA APPROVED (TC-23C) AIR PURIFYING OR
AIR SUPPLIED (TC-19C) RESPIRATORS MAY ALSO REDUCE EXPOSURE. READ
RSPRTR MFR'S INSTRUCTIONS/LITERATURE TO DETERMINE TYPE OF AIRBORNE
CONTAM AGAINST WHICH R SPRTR IS EFFECTIVE, HOW TO PROPELY FIT.
Ventilation:PROVIDE GENERAL DILUTION/LOCAL EXHAUST TO KEEP CONC BELOW
TLV, LEL, AND TO REMOVE DECOMP PRODUCT DURING WELD/FLAME CUT.
Protective Gloves:NEOPRENE, NITRILE, BUTYL, LATEX RUBBER
Eye Protection:CHEM SPLASH GOGGLES WHEN POSSIBLE EXPOS
Other Protective Equipment:WEAR PROTECTIVE CLOTHING, INCLUDING
IMPERMEABLE APRON & GLOVES CONSTRUCTED OF NITRILE, NEOPRENE, LATEX,
BUTYL RUBBER.
Supplemental Safety and Health

HCC:F4
Boiling Pt:B.P. Text:138 TO 242C
Vapor Pres:1.2
Vapor Density:> AIR
Spec Gravity:1.08
pH:UI
Evaporation Rate & Reference:11 (BUOAC=100)
Solubility in Water:0.0%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
SOLVENTS LISTED IN INGREDIENT
Percent Volatiles by Volume:44.90

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS OR STRONG
OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS DECOMPOSITION
PRODUCTS WHEN HEATED. WELDING, BRAZING, FLAME CUTTING SURFACES
COATED W/PRODUCT: CO.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WAS TE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.